Features

Rotor Head

• Machined aluminum center hub.
• Full bearing supported & adjustable seesaw for FAI or 3D.
• Floating feathering spindle with adjustable damping.
• High tilt flybar with rigid flybar control yoke.
• Machined aluminum, full bearing supported bell-hiller mixers.
• Adjustable bell-hiller ratio allows tuning for preferred cyclic response.
• Heavy duty main rotor grips with 5mm long shank blade bolts.
• Blade grips will accommodate any blades with 12mm to 18mm blade roots.
• 690mm symmetrical Aerotech ARF main rotor blades.
• Large one-piece 29gr flybar paddles for sport and 3D flying.
• Two radial bearings and a heavy duty thrust bearing in each blade grip.
• 10mm Hardened main shaft.
• SE, MAX & GAS SE ONLY- Aluminum head button included.
• SE & GAS SE ONLY - RotorTech 700mm carbon fiber main blades.
• GAS - 710mm symmetrical Aerotech ARF wood main rotor blades.

Control System

• eCCPM 3 servos system with bellcranks to absorb rotor head vibration.
• Electronic CCPM (cyclic collective pitch mixing) at 120 or 140 orientation.
• Push-pull dual bearing supported roll cyclic bellcranks.
• Direct dual bearing supported fore-aft cyclic bellcrank.
• Dual bearing supported washout control arms.
• Washout base with brass sleeve for zero slop.
• Machined dual ball bearing CCPM swashplate for 120 or 140 setup.
• 24º Collective pitch range.

Drive Train

• Variable main gear ratio.
• Large diameter slipper clutch that drives the tail during autorotations.
• Clutch bell and lower main shaft bearing block are coupled as one unit for maximum rigidity.
• Adjustable clutch bell gear mesh.
• Large machined clutch bell support by a 15x24 ball bearing.
• Hardened 10 tooth main drive gear.
• Heavy duty clutch provides flywheel effect for smooth idle.
• Torrington bearing start system eliminates start shaft vibration.
• Hardened hex start coupler with 120 set screws.
• Efficient cooling fan with location holes for governor magnets.
• Split collar mast stopper for simple secure main shaft adjustment.
• Machined heavy-duty 14mm delrin gear for heavy loads.
• High quality ball bearings with high quality hardware.
• SE, MAX, GAS & GAS SE ONLY - Constant tail drive unit included.
• GAS & GAS SE ONLY - Machined aluminum squirrel cage cooling fan.
• GAS & GAS SE ONLY - Epoxy fiberglass cooling fan shroud.
• GAS SE ONLY - Removable pull start plate.

Canopy

• High gloss high quality white gel coated epoxy fiberglass canopy.
• Embedded carbon strip reinforcement.
• Pre-drilled mounting holes with rubber grommets.
• Tinted high gloss windshield.
• Pre-cut swashplate, main shaft and starting shaft holes.
• Streamlined aerodynamic design for fast forward flight

Main mechanics

• Rigid stacked modular aluminum mainframe design with continuous machined lower bearing block assembly.
• Fuel tank located on carburator’s centerline for consistent engine operation right side up or inverted.
• Large 22 oz fuel tank for long engine run time.
• Separate front and rear frames permit engine removal with muffler and carburetor attached.
• Rear cross brace and bottom frame plate provides rigidity in all 3 axis.
• Rear engine head design to reduce overall weight and mechanics volume to increase aerobatic maneuverability.
• Lightweight machined aluminum engine mount.
• Extra long battery tray accommodates radio components.
• Convenient and easy access to glow plug.
• Tough, low-profile and flexible landing gear.
• SE, MAX & GAS SE ONLY - 10mm main shaft thrust bearing.
• GAS & GAS SE ONLY - Machined aluminum bottom plate.
• GAS SE ONLY - Triple upper bearing block

Tail

• Tail drive gear off main gear is supported front and back by radial bearings.
• Integrated front tail transmission and tail boom eliminates any potential gear mesh and alignment problems.
• Bearing supported carbon drive shaft with universal end couplers.
• Fully supported carbon tail pushrod with machined aluminum end fittings.
• Large hardened heavy-duty metal tail gears.
• Two radial and one thrust bearing in each tail rotor blade grip.
• Rear rudder servo mount for direct and smooth tail control.
• Bearing supported tail pitch lever designed for optimal linear tail pitch.
• Flexible 3D style horizontal and vertical tail fins.
• Extra large 5x13mm tail output shaft bearing.
• Strong lightweight aluminum tail boom.
• Dual aluminum tail boom support struts.
• Flexible and lightweight 4.5gr 95mm tail blades.
• Hardened steel tail output shaft.
• SE, MAX & GAS SE ONLY - Dual carbon support struts and support bridge.
• SE, MAX & GAS SE ONLY - Carbon horizontal and vertical fin set.