CA/Locker/Oils/lube

Superthin CA

INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. 3rd largest bottle shown

103 Superthin CA 2oz
Weight: 0.10 kg

Insta Cure - Filling CA

INSTA-CURE is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 25mm separations on one surface, then assemble the parts, letting the pressure spread the CA out. 3rd bottle shown (50g)

108 Cap filler CA 2oz
Weight: 0.10 kg

IC2000 CA rubber toughened

IC-2000 is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 10 seconds, which can be accelerated with INSTA-SET. When cured, IC-2000 is pliable enough to be carved with a hobby knife. IC-2000 is the best adhesive for R/C car tires. is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces.

120 Rubber tough 1 oz
Weight: 0.10 kg

5 min epoxy glue

QUIK-CURE epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldnt be used in areas that are subject to long-term immersion in water. QUIKCURE is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE can be handled after 5 minutes. Full strength is reached in 30 hour. 4.5 oz size. 5min shown for package detail.

201 5min Epoxy
Weight: 0.10 kg

15 min epoxy

QUIK-CURE epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldnt be used in areas that are subject to long-term immersion in water however, it works fine for the internal structure of wood framed boats. QUIKCURE is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE can be handled after 15 minutes. Full strength is reached in 1 hour. 4.5 oz size. 5min shown for package detail.

205 Quikcure Epoxy
Weight: 0.10 kg

30 min epoxy

A 30 min clear epoxy in 25ml (50ml total)

VB282- 30 min epoxy
Weight: 0.10 kg

JB Weld

Ideal for metal filling/metal to metal connection and for retapping holes etc. 2 part mix. Can secure most metal to metal parts. Ideal for making up metal infills etc. Very strong and can withstand fuel and temperatures upto 150 oC.

JB Weld VB8270
Weight: 0.10 kg

Antistatic spray

Wondered some times why that tail kicks or you get a lock out on a helicopter? Some tail belt drive systems can cause static build up which cause glitches on your receiver, this effect can cause lock out and loss of your helicopter. One spray we flying session on to the belt on the toothed side will minimise the friction to the belt which will help reduce any static build up. 200ml spray.

RE73 spray
Weight: 0.20 kg

3 in 1 lube oil

Ideal for light lube of moving parts. Also protects exposed metals from rust.

163073
Weight: 0.20 kg

Silicone Grease 50g

A tube of 50g of silicone grease for application on to plastic gears etc to reduce drag and gear chain noise. Can also be used as necessary as a multi purpose grease. -5 to +200 oC operating temps.

RE90
Weight: 0.20 kg

Standard CA Superglue 20 ml

VB291
Weight: 0.01 kg

28g Devcon 5min epoxy - The best

S205
Weight: 0.10 kg

VB414 chemical metal cleaner

A spray cleaner which will remove all gum from engines etc, care should be taken when using this product and use as directed on the can with a sample area to test. Will make you old metal parts look like new.

VB414
Weight: 0.10 kg

Nutlocker and Thread locker

Pro range nut locker in 10ml bottle, ideal for use of parts that work loose or require nut locker, joints can be broken using a mechanical strength ie tools.

VB450
Weight: 0.10 kg

Studlocker

Pro range stud locker in 10ml bottle, ideal for full lock joints where a large amount of force/pressure is required to release the joint. Very strong retaining pressure and can also be used for certain bearing retaining purposes for metal to metal contact.

VB451
Weight: 0.10 kg